â— Flatbed transporter Flatbed transporter is also called construction machinery transporter and it is mainly used to transport non-detachable objects like excavators, loaders and harvesters.
Its varieties include Dongfeng Jinba flatbed transporter, FAW Jiefang Flatbed Transporter and other flat-panel transporters, and semi-trailer flatbed transporters. The cargo loaded is between 3 tons and 30 tons and is suitable for long-distance transportation of construction machinery and some non-removable goods.
Flatbed trucks are used to transport construction machinery, excavators, forklifts, harvesters and other construction machinery. The rear part of the truck is equipped with ladders and legs. Suitable for long-distance transportation of construction machinery and some non-removable goods.
â— The flatbed transporter must check the basic situation before starting the pre-transportation flatbed transporter. It depends on whether there is any obstruction around the flatbed transporter; there is suspicious oil and water on the floor of the flatbed transporter; the platform transporter chassis Tyre pressure is sufficient. Tyre pressure is an important factor affecting the safety of the flatbed transporter because the flatbed transporter compresses and expands the tires during transport. This is the so-called tire deformation, especially when the tire pressure is low and the vehicle speed is high. Obviously, at this time, the internal temperature of the tire is abnormally high, which may cause separation of the rubber layer and the cover layer, or breakage and scattering of the tread rubber, which may cause a tire burst and cause a vehicle accident. Therefore, in any case, the tire pressure of the flatbed truck must be guaranteed at the manufacturer's standard. Whether the tire pressure is appropriate or not has a great influence on the fuel economy of the flatbed truck. Improper tire pressure will increase the rolling resistance of flatbed truck tires, thereby increasing the fuel consumption of flatbed trucks.
â— Maintenance of flatbed trucks Flatbed trucks should pay attention to the following points: 1. The connection between the supercharger and the intake and exhaust pipes of the flatbed truck must be tightly closed. If there is a leak between the exhaust pipe and the exhaust turbine, The supercharger efficiency will be greatly reduced and the exhaust temperature of the diesel engine will rise sharply to damage the Valve and the supercharger.
2. Before starting the new machine, the supercharger and supercharger oil filter must be filled with clean oil to ensure that the diesel engine moves together and the supercharger bearing can be lubricated.
3. Before the diesel engine is stopped, the flatbed truck shall be operated for 3-5 minutes under idle conditions, so that the speed of the supercharger will drop, the temperature will decrease, and the supercharger operation sound will be monitored. If abnormality is found, it should be stopped and checked. If the turbocharger rotor is inflexible and there is stuck or worn sound, it must be sent to a conditional repair station.
4. After the flatbed truck has been operated for 500h or 30,000km, the clearance on the rotor shaft of the supercharger should be checked and dust and coke on the turbine shell and rotor blades of the compressor should be removed. At this point, the turbocharger must be removed from the diesel engine and the metal gasket between the supercharger exhaust pipes replaced. Mechanical methods are not allowed to remove scale on the rotor components, but instead use gasoline or other cleaning liquids for cleaning aluminum parts.
5. Plate transporter turbocharger compressor lock Nut can not be removed, otherwise it will destroy the turbocharger rotor dynamic balance, causing turbocharger damage.
6. Flatbed trucks, do not damage or deform the rotating parts of any turbocharger that has been removed, otherwise it will affect the balance of the turbine of the flatbed truck. Also do not damage any rubber seals.
Features The use of high elastic solid tires, can enhance the trailer load capacity and service life, to reduce the damage caused by the vehicle bumps on the goods during driving; Double floating suspension bracket can be used to adjust the balance and stability of the flatbed car; The shaft material is made of alloy steel and processed by special processing. The design is reasonable and the I-beam main beam is adopted to increase the bearing capacity and improve the stability of the entire vehicle.
Xia Gong Chu Sheng (Hubei) Special Vehicle Manufacturing Co., Ltd. Sales Manager Deng
Stamping Parts, Stamping,Metal Processing Machinery Parts,Stamping Die
Water Manifold,Pipe Clamp Co., Ltd. , http://www.nbpipefittings.com