The series pumps are designed as irrigation and drainage equipment with motor and downside pup body.These pumps can be applied to discharge the sewage from building site,coal mine,metallurgy,printing and dyeing enterprise and spinning mill,also applied in irrigation and drainage of clear water.Some ode pumps use fluid channel impeller to raise the anti-jam capacity.Some model pumps are designed according tall-lifting theory to make the pump to keep non-overloading run under the normal working situation.The design extends the using lift-span of motor effectively.Advanced foreign technique were introduced and absorbed in the cutting type series submersible pump.The pumps are designed to cut or manage the long fiber,plastic bag to keep the pump unblocked.
Â
Materical
Pump body: Cast iron
Motor housing: Cast iron
Impeller: Cast iron
Motor wire: Copper
Shaft: 45# steel
Â
OPERATING LIMITS:
Trans medium PH 4-10
Fluid temperature limit:<40ºC
Max ambient temperature: 40ºC
Operating depth: 5m
Insulation Class:E
Protection Class:IP68
WARRANTY: 1 YEARÂ (according to our general sales conditions)
Main Technical Parameter   Â
Item No | Voltage | Frequency | Power | HP | Flow rate | Head | Speed | Outlet | Float Switch |
(Hz) | (KW) | (m³/h) | (M) | (R/min) | (Inch) | ||||
WQD8-10-0.55 | 220V | 50Hz | 0.55 | 0.75 | 8 | 10 | 2860 | 2" | can add |
WQD6-16-0.75 | 220V | 50Hz | 0.75 | 1 | 6 | 16 | 2860 | 2" | can add |
WQD10-12-0.75 | 220V | 50Hz | 0.75 | 1 | 10 | 12 | 2860 | 2" | can add |
WQD7-15-1.1 | 220V | 50Hz | 1.1 | 1.5 | 7 | 15 | 2860 | 2" | can add |
WQD15-9-1.1 | 220V | 50Hz | 1.1 | 1.5 | 15 | 9 | 2860 | 2" | can add |
Workshop
Â
LINA Extrusion Pelletizer
Most of the polymer must be kneaded and then granulated before it is made into a final product. Sorted by pelletizing ways, LINA rubber & plastic granulator can be divided into four categories: 1. Hot-cutting and air-cooling pelletizing method. 2. Under-water granulating method. 3. Water-strand extrusion method. 4. Water-ring granulation method. LINA pelletizer can meet the granulation needs of high-viscosity and low viscosity rubber and plastic materials, as well as some new materials and chemical additives.
LINA Die Surface Hot Cutting Pelletizing Machine
LINA`s die surface hot cutting and air cooling granulating machine is suitable for polymers that are sensitive to heat and long residence time, such as PVC, TPR, PE, cross-linked PE and so on. The flow path of the polymer from the extruder to the pelletizing port should be kept as short as possible with minimal heat. When polymer is extruded through the die surface, the rotating blade cuts the extruded materials into particles. After the pellets are cut, they are removed from the rotary blade and caught by cooling air circulating in the pelletizing room. The air stream preliminary cools the surface of the pellets and takes them out of the pelletizing room and sends them to the cooling zone.
Assembly Ling Diagram of LINA Die Surface Hot Cutting Granulator
Advantage of LINA Pelletizing Line
1. The unit has the whole unit process chain, sound and light failure alarm and fast lock fault point and other control functions. All parts that are in contact with the material are made of stainless steel.
2. High accuracy of temperature control system to ensure the temperature sensitivity of the material.
3. It adopts the drop type separating method after cutting process, to avoid Particle agglomeration and ensure particle cooling.
4. Feeding system of the pressing machine adopts heater and reversing device to solve problem of power outage, material crash and cleaning.
5. Especially, the barrel and die head adopts advanced foreign techniques to ensure and control the dangerous occurred when the pressure is uncontrollable. The honeycomb filter plate is easy to clean and quickly change the mesh and the die head t easy to leak.
6. The hoist adopts automatic return technology to ensure the working efficiency.
7. The technological combination of dual-pull forced feeder and single screw not only meet the high requirement of secondary continuous mixing, but also solve the problem of time and power consuming of traditional working process.
Specifications of LINA Extrusion Granulating Line
Name |
Mode |
Capacity of Kneader |
Screw length to diameter ratio |
Screw diameter |
Dimension |
LINA Extrusion Pelletizing Line |
LN-10/70 |
10L |
12:01 |
70mm |
2200*1000*1150 |
LN-10/75 |
10L |
12:01 |
75mm |
2650*1100*1250 |
|
LN-35/100 |
35L |
12:01 |
100mm |
3800*1090*1690 |
|
LN-55/120 |
55L |
12:01 |
120mm |
3800*1090*1690 |
|
LN-75/135 |
75L |
12:01 |
135mm |
3850*2350*3280 |
|
LN-110/150 |
110L |
12:01 |
150mm |
5100*2000*1500 |
|
LN-110/165 |
110L |
12:01 |
165mm |
5100*2000*1500 |
Hot Cutting Extrusion Pelletizer
Hot Cutting Pelletizer,Hot Cutting Pelletizing Line,Hot Cutting Pelletizing Machine,Plastic Hot Cutting Granulator
LINA Machinery Industrial Co.,Ltd , https://www.linakneader.com