Main function of the skiving machine is to peel the exterior rubber of the rubber hose and contain steel wires, so as to connect ferrule. The machine is convenient and high efficiency.
Â
Operation instruction
Â
Insert the hose into the hole of skiving machine, push the hose forward step by step. The axis is stationary, motor drives the knives pole rotating. When the hose move forward, the exterior rubber is peeled by the knives. Pull the hose out after the work finish.
Â
Before power on the skiving machine, please put the peeling axis into the fitting axis collar and fasten it firmly. Then fix the knives on the knife pole, and adjust knives to a normal position. Warning, check the screws and fitting and keep them in good condition status. After all these works are confirmed, start the peeling machine, then try to skive one hose. If the rubber could not Â
be skived completely, adjust the hand of knives to the center, so as to the knives could skive more deep. If the hose is spiral type steel wires hose, start the switch according to the direction of steel wires. The turning direction of the knives are accord with the turning direction of the switch.
Â
 Â
Skiving range | 6-51mm |
Amount of dies | 10 sets |
Mold number | 6,8,10,13,16,19,25,32,38,51 |
Operation mode | Manual |
power | 0.75/1.5(Optional) |
Voltage | 220V/380V(Optional) |
Efficiency | 1500 pieces/hour |
Dimensions of product | 620*470*1050mm |
Dimensions of Package | 700*520*1160mm |
Weight | 65KG |
If you are interested in any of our products,please don't hesitate to contact with us. automatic hydarulic hose stripping machine
Main function of the skiving machine is to peel the exterior rubber of the rubber hose and contain steel wires, so as to connect ferrule. The machine is convenient and high efficiency.
Â
Operation instruction
Â
Insert the hose into the hole of skiving machine, push the hose forward step by step. The axis is stationary, motor drives the knives pole rotating. When the hose move forward, the exterior rubber is peeled by the knives. Pull the hose out after the work finish.
Â
Before power on the skiving machine, please put the peeling axis into the fitting axis collar and fasten it firmly. Then fix the knives on the knife pole, and adjust knives to a normal position. Warning, check the screws and fitting and keep them in good condition status. After all these works are confirmed, start the peeling machine, then try to skive one hose. If the rubber could not Â
be skived completely, adjust the hand of knives to the center, so as to the knives could skive more deep. If the hose is spiral type steel wires hose, start the switch according to the direction of steel wires. The turning direction of the knives are accord with the turning direction of the switch.
Â
 Â
Skiving range | 6-51mm |
Amount of dies | 10 sets |
Mold number | 6,8,10,13,16,19,25,32,38,51 |
Operation mode | Manual |
power | 0.75/1.5(Optional) |
Voltage | 220V/380V(Optional) |
Efficiency | 1500 pieces/hour |
Dimensions of product | 620*470*1050mm |
Dimensions of Package | 700*520*1160mm |
Weight | 65KG |
If you are interested in any of our products,please don't hesitate to contact with us.
For iron scraps, whether it's turnings, chips, filings, shavings, cuttings, sawdust, drillings, borings, debris, granules or sludge, Ecohydraulic iron recycling machine can help. If your scraps are small chips, you can choose our Iron Briquette Machine to press your chips to be small blocks. If your scraps are shavings or turnings, you can choose our Iron Baler to press your chips to be square bales, if your scraps are big like pipe tube sheet plate rebar, etc., you can choose our iron shear to cut your scraps to be smaller pieces.
Iron Shavings Recycling Machine, Iron Turnings Recycling Machine, Iron Scraps Recycling Machine, Iron Chips Recycling Machine, Waste Iron Recycling Machine
Jiangyin Metallurgy Hydraulic Machinery Factory , https://www.eco-balers.com